As a Seattle Home Inspector I frequently find insulation tightly packed around B-Vent pipes that run through attics. So, even though rockwool is not considered combustible, it too must be retained away from the vent pipes because the insulation itself will conduct heat to things that can burn. …

Can you put insulation around vent pipe?

You must have a 6-inch clearance between single-walled vents and any combustible material, such as insulation. … A double-wall or dual vent pipe consists of 2 layers of metal and requires a 1-inch clearance.

Can insulation touching flue pipe?

Fiberglass insulation can’t and should not touch your stove’s vent pipe. While fiberglass is not flammable, it can melt, causing fire risks. To get around this issue, you need to install a barrier of aluminum flashing between the vent and the insulation.

How hot does the outside of B vent get?

Type B Vents any appliance that produces flue gasses that exceed 480° F (249° C).

Can you paint B vent pipe?

Yes, you can paint exposed b-vent to match the color of the siding or roof shingles. Yes, you can paint exposed b-vent to match the color of the siding or roof shingles. … Scuff and clean the surface to be painted with steel wool. Clean dust, oils and fingerprints off the surface using a household degreaser cleaner.

Can I put insulation around my furnace?

Insulating the walls and ceiling in a furnace room can reduce heating costs and make the furnace more energy-efficient. Rigid foam insulation is attached to the walls with adhesive, and to the ceiling with adhesive and roofing nails. … In large furnace rooms and basements, the job is easier with the help of an assistant.

Can I put insulation around a dryer vent?

Whether you should insulate your dryer vent or not depends on its location. If the dryer duct is within the home or a heated basement, there is no need or reason to insulate the duct/vent pipe. However, if the dryer duct runs through an unheated basement or crawlspace—insulation is highly recommended.

Should furnace be hot to touch?

Most single stage furnaces should be just uncomfortable to touch on the main trunk just above the main unit. As Heat rise levels can range from 50-70 higher than ambient air temp. Yes, it’s normal.

Should pipe coming out of furnace be hot?

It’s normal for your exhaust pipe and the exhaust to feel warm. It’s also normal to see icicles or other icy build-up around the pipe during freezing weather. If your pipe is very hot, call Breedlove Dobbs so we can have an experienced and qualified technician check it out.

Why is my furnace running so hot?

One of the most common and simple causes of an overheating furnace is poor air circulation. The internal components of your furnace can get too hot when there isn’t good airflow. This usually happens when you forget to change your air filter regularly.

Article first time published on

Can insulation touch double wall pipe?

Double-walled metal chimneys should not have insulation touching as already mentioned, that can create a hot spot since the heat cannot dissipate.

Can fiberglass insulation touch chimney?

Fiberglass insulation is naturally fire-resistant. This makes it an ideal insulation material for use in areas that experience high temperatures. As such, it can be used to insulate a chimney. … Fiberglass will not burn, but it may melt if temperatures exceed 212 degrees Fahrenheit.

Can insulation touch gas fireplace?

Insulating Gas Fireplaces Unfaced batt insulation may be pushed into the opening between the gas supply pipe and the access hole. The fireplace itself is heavily insulated and you should not install insulation into the walls surrounding the firebox.

Should you caulk around air vents?

Air leaks that occur in vent ducts must be sealed not only to prevent air from escaping from the system but to save money on energy bills as well. One way to seal vent ducts is to apply caulking to fill in gaps. You can seal vent ducts with caulking by first examining the vent ducts for leaks or gaps.

How do you insulate a rectangular duct?

When insulating HVAC ductwork, use a foil, faced fiberglass insulation with an R-6 or higher R-value. Use the type of metallic foil duct tape recommended by the insulation manufacturer to seal and hold the insulation in place. Make sure the foil surface of the insulation is free of dust before applying the tape.

Can insulation touch heating ducts?

Fiberglass insulation can touch HVAC ductwork provided the ducts are not leaking or forming too much condensation. The insulation should be snug enough to prevent significant gaps throughout the ductwork.

Should you paint roof vents?

Black ABS pipes or PVC roof vents that are used to vent drain and sewer lines, generally, should be painted. This is also often recommended for water heater or furnace vents, if PVC material. The paint helps protect the pipes from the suns UV rays.

Can spray foam be used around dryer vent?

Spray foam or silicone caulk are ideal for sealing dryer vent gaps, and provide a durable seal that blocks pests and eliminates air infiltration, says the Centers for Disease Control and Prevention. The product you should use depends on the size of the gap you need to seal.

What type of insulation is used for dryer vents?

A: You can actually use any type of insulation, the same as if you’re insulating heat ducts. You can use the actual rolled insulation that’s made for wrapping ducts, or just use some unfaced fiberglass — R-11 separated in half lengthwise is fine. Secure the insulation by tying it in place with nylon twine.

How do you insulate outside dryer vent?

Slowly spray canned foam insulation into the gaps, as it swells once it makes contact with a surface and it’s easy to spray too much if you’re not careful. Wait for the spray foam to dry or cure. If you oversprayed the foam insulation, remove the excess insulation after it dries; wear work gloves for this task.

Is Fiberglass insulation flammable?

Fiberglass and mineral wool insulation Materials are noncombustible, and remain so for the life of the product. They require no additional fire-retardant chemical treatments—in fact, unfaced fiberglass and mineral wool are accepted as a fire block in wood frames.

Should a furnace be insulated?

While it’s not necessary that the furnace vents are insulated, it is essential that they are sealed properly. You may be surprised to learn that the vents can cause you to lose anywhere from 20 to 35% of cool or heated air if they are leaky.

How hot does a direct vent pipe get?

Hence the protective screen that is placed in front of the glass. The area surrounding the fireplace can get hot as well when a fire is burning—in some cases, it can get as hot as 190 degrees.

What should my furnace flue temp be?

Bottom Line. For maximum efficiency, your flue pipe temperature should be in the range of 175 to 280 degrees Celsius or 350 to 540 degrees Fahrenheit, according to Natural Resources Canada.

How long can a furnace exhaust pipe be?

The maximum vertical distance you can run a furnace exhaust vent is about 15 feet. If there is a forced air inlet within 10 feet of the exhaust vent, the exhaust gas ventilation terminal should be positioned at least 3 feet above it.

Why does my furnace stop working when it's cold outside?

THE FIX: Simply changing the air filter could be your solution. A dirty or clogged air filter is likely to impeded airflow, leaving your furnace to overheat. Another thing you should check are the vents around your home. Make sure none are blocked or shut, as that could be causing the airflow problem.

Why does it smell like burning from my furnace?

Normal dust burn-off When the furnace isn’t actively heating, dust and dirt particles can settle inside the furnace and on internal components. When you turn on the furnace the dust burns off, causing a light burning smell that should dissipate relatively quickly.

How do you reset a furnace after overheating?

1. Turn down the thermostat to its lowest setting.
2. At the circuit breaker, turn off the power to the furnace.
3. If this is a gas furnace, turn off the gas supply at the valve for the main gas pipe, but leave the pilot’s gas supply on.
4. If the pilot light was out, light a match to relight it.

Why does my furnace come on every 5 minutes?

A dirty filter can cause the furnace to overheat. Short cycle time: 2-5 minutes. … If the furnace gets too hot, the switch shuts down the furnace. A dirty filter prevents a flow of fresh, cool air into the furnace to be heated and dispersed.

How do I cool down my furnace?

1. Moving the sample into a cool area.
2. Movable insulation panels (manual or automatic)
3. Ambient air blown into furnace or oven.
4. Ambient air blown around inert gas retort.
5. Cycling of inert gas atmosphere through a water cooled heat exchanger.

Why is the furnace blowing cold air?

Therefore, your furnace blowing cold air could result from a clogged or dirty air filter. If you have a dirty or clogged furnace filter, the cool air from inside your home will struggle to travel past through it and into the furnace. This means you have insufficient air to heat and redistribute.