Simply put, too much detergent was used and an excessive amount of suds or foam was produced. Adding an additional rinse cycle without adding any more detergent might fix this problem. Sometimes the machine will automatically detects this problem and add a pause and additional rinse cycle in order to break up the suds.

What do you do when your washer says SD?

When “Sud” or “Sd” is displayed, the washer automatically extends the rinse time to remove the excess suds. During this time, the washer pauses the tumbling and adds water for additional rinsing. This pause allows the bubbles in the suds to break.

How do I clear the error code on my Kenmore washer?

1. Look for the “Pause/Cancel” button on the washer control panel. …
2. Press the “Pause/Cancel” button twice to cancel the wash cycle. …
3. Connect the water supply hoses back to the washer and turn on the water spigots.

How do I fix the Sud error on my Kenmore washer?

SUD : The Sud error code is used to indicate there are too many suds for the washer to remove. This is often caused by too much detergent being used or non HE detergent being used in an HE machine. Run the machine through a Rinse/Spin cold water cycle then a Normal cycle without adding any additional soap.

How long does Sud error last?

If you have noticed a SUD code during a washing cycle, it means the suds have exceeded the drum’s usual level. More specifically, this error means that the washing machine is reducing foaming. It has just stopped for 5-10 minutes to allow the suds to dissipate and the washing cycle to go on.

Why does my Whirlpool washer keep saying SD?

Sud or Sd is displayed: There are too many suds in the washing machine. The washer will not be able to spin out water with the excess suds. When “Sud” or “Sd” is displayed, the washer automatically extends the rinse time to remove the excess suds.

Why does my Kenmore washer says Sud?

If “Sud” is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent.

Why does my washer keep saying Sud?

If your washing machine has the word “SUDS” on the display, it has detected an over-sudsing condition, and will stop for a short period to allow the suds to dissipate. This error code is usually caused by too much detergent, or the wrong type of detergent. … Be sure to reduce the amount of laundry detergent accordingly.

Why is my washer flashing SD?

This error code indicates excessive detergent suds occurred during the cycle. This could be caused by using too much detergent or not using High Efficiency (HE) detergent. The washer will not be able to spin out water with the excess suds.

How do I reset my Kenmore Elite Smartwash quiet Pak 9?

1. Press and hold “Drain & Spin” for three seconds to release the child lock, if the keypad is locked. …
2. Press “Pause/Cancel” twice to cancel the current operation.
3. Turn off and unplug the washing machine.
4. Wait several minutes before restoring power to properly reset the machine.

Article first time published on

Where is the drain pump on a Kenmore washer?

The drain pump is located in the lower front corner of most Kenmore front-loading machines, and the most difficult part of the job may be getting to it. If the machine doesn’t have an access panel, as some do, you’ll have to take the entire front panel off.

How do I unlock my Kenmore Elite washer?

1. Touch “Control Lock” for five seconds until “CL” disappears from the washer’s display to unlock the control panel.
2. Press “Start/Pause” to manually pause the cleaning cycle. …
3. Pull the door’s handle to open the door and add or remove the clothing from the washer.

How do you reset a Kenmore front loader?

To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.

How do you put a Kenmore front load washer in diagnostic mode?

1. With the washer empty, close the door.
2. Push “control/on” or “Start”
3. Select “Drain/Spin”
4. Select “No Spin” by pressing SPIN SPEED touchpad.
5. Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
6. C:00 should light up and begin the diagnostic.

How do you run a diagnostic test on a Kenmore washer?

How do I put it into diagnostic mode? Turn the dial to Drain/Spin, Press Pause/Cancel to turn off the control. Within 5 seconds, press and hold PAUSE/CANCEL and OPTIONS until the LED’s start chasing. Turn the dial one click clockwise to test each of the washer components (water valves, door lock, and motor).

How do I fix my SUD error?

The washer has detected too many soap suds; it should pause automatically and wait for the suds to dissipate. Making sure you are using a high-efficiency detergent, not using too much detergent, removing detergent residue from the washer, and cleaning the drain pump filter should resolve the issue.

What does sus Loc mean on washing machine?

“Sud LOC” (suds lock – I have too many suds) Your machine has a suds build-up. Too much detergent may have been used for the amount of soil in the load. Ensure that you are using a HE, Low Sudsing, Matic or Front Loader type detergent. Wait for suds to dissolve (about 20 minutes).

What does the code 5d mean on a Kenmore washer?

The 5d code is actually an Sd code and it means suds have been detected in the washer. This can indicate to much soap or the wrong kind of soap was used in the washer. Be sure HE detergent is being used. If can also indicate the drain pump is restricted or the drain hose is kinked.

What does F mean on Kenmore Elite washer?

The F indicates that the washer control detected a component problem. … If the F code was caused by excessive suds preventing the washer from draining, you may be able to shut the door and run a drain/spin cycle to remove the water from the washer.

How do I fix the Sud error on my Whirlpool washer?

To solve this SUDS issue, finish your current load, if possible. Then run the washer on the largest load possible with no detergent and using hot water. This should rinse away the excess. However, if it still feels slimy inside, you may need to repeat as necessary.

How do I fix 5d error on Whirlpool washer?

To solve the problem correctly, you need to press two times on PAUSE / CANCEL or 1 – on POWER, and then start washing. Stop the washer and take out items that are too bulky, soft, or fluffy. After that, continue the started cycle. The 5d error should go away because the sensor was reacting to swollen woolens.

What does F35 mean on a Kenmore Elite washer?

The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor.

What is F21 on Kenmore Elite washer?

@gwenr Error F21 is a Long Drain error. If the drain time exceeds 8 minutes this error code will be displayed. In addition, a “SUDS” error may also be displayed. This may be an indication of a drain pump problem and/or clog in the drain line.

Why won't my Kenmore Elite washer turn on?

First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. … To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.

How do I know if my washing machine drain pump is bad?

Check the pump pulley by removing the pump from the washer and trying to rotate it by hand. If the pulley doesn’t turn freely and is frozen or stiff, replace it. Also, if the agitator is moving but the tub isn’t, this is a sign the pump is dying.

Why won't my Kenmore washer unlock?

If the washer door won’t unlock the problem might be the main control board. This is not common. Normally the problem is with the lock mechanism. Unplug the machine for 5 minutes to let it reset and then plug it back in and give it a try.

What does sensing mean on a Kenmore washer?

First, What is the Sensing Cycle? The auto-sensing function on your Kenmore HE washer is designed to conserve water and automate the entire washing process. It helps ensure that just the right amount of water is used to wash your load of laundry.

How do I reset my Kenmore Super Capacity 3.5 washer?

Turn off and unplug the machine. Plug the washer back in and wait for the control panel to light up. This resets the washer back to the original factory settings.