If you use a high-quality exterior wood stain like Olympic Elite stains, it can take a full 24-48 hours to cure, depending on the moisture level within your deck as well as the quality and condition of the wood your deck is made from.

How long does Olympic stain need to dry before rain?

Robust resin systems promote adhesion between the stain and your wood. So, rain can fall on your deck only 8 hours after being freshly stained with MAXIMUM clear, toner or semi-transparent stains. MAXIMUM solid color stain takes only 12 hours to be ready for rain.

How long does a stain take to dry?

On average, stains take around 24 to 48 hours to dry. Some brands or stain types may take longer or up to 72 hours. Many factors go into the drying time. Double-check the instructions on the label for the exact dry time.

How long before you can walk on Olympic stain?

After you’re done, give the stain between 24-48 hours to dry completely before replacing furniture or walking across the surface.

How long should you wait for wood stain to dry?

While conventional stains recommend 18 to 24 hours drying time, Minwax® Performance Series Tintable Interior Wood Stain can be recoated in just 2 hours with oil based finishes and 6 hours with water based finishes. That means you can apply stain and two topcoats in a single day without sacrificing varnish clarity.

Can you stain a deck if it is wet?

It is not recommended to stain a wet deck. … Let the deck dry for at least 48-72 hours before staining. Staining a wet deck will result in an uneven finish. Try to stain your decking on a dry, warm day.

What if it rains after staining deck?

If it rains within 48 hours after you apply the stain, the water will soak into the wood pores and try to displace the stain. This will result in a splotchy surface rather than an even tone. If it rains right after you apply the stain, the stain will peel and flake off.

How many coats of stain should you apply?

2 coats. To deepen the color, apply a third coat. Optional, for additional luster or sheen a clear protective finish can be applied. Recommended finishes include Minwax® Fast-Drying Polyurethane or Minwax® Wipe-On Poly.

How long do you have to stay off a stained deck?

In most cases a full body stain or acrylic deck finish will be dry to touch within an hour in dry, hot weather. After two hours you could take a chance and walk on it with shoes, though I’d recommend barefoot. After about 4 hours you should be able to safely walk on your deck.

Do you have to poly over stain?

You don’t necessarily have to seal stained wood with polyurethane. There’re several other sealers and clear coats for stained woods, such as lacquer and Minwax Polycrylic, that you may use over stain. What is this? A polyurethane topcoat is one of the best protective clear coats available for use on stained wood.

Article first time published on

Is stain supposed to be sticky?

Stain becomes sticky on a wooden surface because it doesn’t have a binder, such as you find in paint or varnish. When the solvent evaporates, all that remains is the pigment and the oil that is carrying it. An easy way to remove this is simply to apply another heavy coat of stain.

Is it OK to stain wood in the sun?

Extreme heat or sun can work against you when you are staining your deck. The direct sunlight can cause the deck to dry too quickly which will leave water marks. If the weather is forecasting for no rain, and you can expect the temperatures to be below 80 or 85 degrees Fahrenheit, make a plan to stain your deck.

How do you make stain dry faster?

1. Add a Compatible Drying Agent to the Wood Stains. …
2. Use a Space Heater. …
3. Turn Up the Thermostat. …
4. Use a Dehumidifier. …
5. Use Your Indoor Air Conditioners to Decrease the Indoor Humidity Level. …
6. Use Portable Fans or Your Overhead Fan to Increase the Airflow. …
7. Open the Windows to Increase Airflow.

Can I apply 2 coats of Cabot stain?

Precautions: Two coats applied to a non-porous surface will result in a higher sheen. Always test a small area prior to applying a second coat. Do not apply in direct sunlight, to hot surfaces, or when air or surface temperature is below 50°F or may fall below 50°F for 48 hours after application.

What happens if you apply second coat of stain too soon?

If you apply a second, unnecessary coat of stain to wood that is already adequately covered, you risk creating a tacky surface that is prone to early peeling because the second coat is not penetrating the wood surface, but simply laying on top of the first coat of stain.

Why is the stain not drying?

If you applied the stain correctly, and it still remained tacky, it could be due to rainy weather or high humidity. … In either case if the tackiness doesn’t go away, wipe the wood down with mineral spirits or naphtha to remove most of the stain, let it dry thoroughly, then try again using a fresh can of stain.

What if it rains 12 hours after staining deck?

It Rained Shortly After Staining my Deck It is best to never stain any exterior wood when inclement weather is forecasted, especially rain. Most deck stain brands will warn against the application of their product within 12-24 hours of rain being forecast. … You cannot do much until it stops raining once it starts.

How long after staining deck can it rain?

Applying Stain First, ensure the deck is completely dry. Remember, no rain 24 hours before you apply stain and no rain 24 hours after the staining project. Assuming the deck is dry and thirsty for stain, it’s time to make your deck amazing.

When's the best time to stain a deck?

The best time to stain your deck is either the spring or the fall. If you stain your deck in the summer, make sure you do it out of the direct sunlight. Applying a deck stain in direct sun will cause the stain to dry to quickly and can result in premature stain failure.

How many coats of stain should you put on a deck?

The general rule of thumb is to apply only as much deck stain as the wood can absorb. Typically this will be 2 coats, unless your dealing with extremely dense hardwoods which may only be able to absorb 1 coat of wood stain.

Can you pressure wash and stain a deck in the same day?

DPI Pressure Washing recommends you wait 72 hours following cleaning to stain your deck. If it rains on one of the days afterwards, you’ll have to wait again, but it will be worth it.

Should I pressure wash my deck before staining?

There is a common misconception that just pressure washing a deck prior to staining is all you need to do in order to prep your deck for stain. Pressure washing can help, but if you want your stain to last, using a good deck cleaner and brightener on the deck prior to pressure washing will provide you the best result.

Can I put a second coat of stain on my deck?

Yes. You can apply an additional coat of stain after 24 hours if you want a darker wood color, especially if the first coat takes longer to dry. Just be sure to apply the stain coat the same way you did the first, and wipe off the excess.

When can I put furniture back after staining deck?

I would wait at least 24-48 hours before moving patio furniture back on the deck and returning it to active use.

Can you touch up deck stain?

When the deck is again dry, if there are relatively few bare spots, touch those up, wait three or four hours, then give the whole deck a fresh coat. If there are lots of bare spots, skip the touch-up and just give the whole deck two coats.

Can you put stain over stain?

Staining over stain is easy and works beautifully if your applying a dark stain over a lighter stain on raw wood. 2. You can mix 2 or more stains together to make DIY custom stains.

Can I stain wood twice?

Keep good records so you can duplicate what you have done if you need to. Leave the stain on the wood longer before wiping it off. … Apply a second coat of stain after the first has dried fully. This will usually produce a darker coloring, but it adds a step to the process and slows production.

Should I sand after staining?

You should not sand after staining. Keep in mind that stain is not a durable finish and requires a clear finish over it. To stain properly you should first sand the wood, then dampen it with a barely-wet sponge, allow it to dry, and sand again… then apply the stain.

Do you have to seal after staining?

After staining wood do you have to seal it? … After staining wood, you have to seal if because the wood remains a porous surface. If you’re just using a regular stain, it can provide some degree of protection compared to totally unfinished wood.

Why does my stained wood feel sticky?

If you applied the stain correctly, and it still remained tacky, it could be due to rainy weather or high humidity. … In either case if the tackiness doesn’t go away, wipe the wood down with mineral spirits or naphtha to remove most of the stain, let it dry thoroughly, then try again using a fresh can of stain.

Can you leave stain on without wiping?

Stain can be left on without wiping off. However, the heavier the application of stain, the longer it takes to fully dry before a topcoat can be applied. Typical stain dry time before recoating is 1-2 hours. Leaving stain on without wiping off creates the richest, darkest shade of the stain on the wood.