The agitator coupler connects the agitator to the agitator shaft. … Be sure to clean any dirt, rust, or residue off the transmission spline grooves, and make sure the grooves on the agitator splines are clean and undamaged. We recommend using the gasket and bolt that come with the replacement coupling.

How do I know if my agitator coupler is bad?

If the washer fills to the selected level and you hear the motor running but the washer is not agitating, set the dial on the spin cycle. If the washer drains the water and you hear the motor running (making noise but not spinning), it is likely you have a broken motor coupler.

Why is my GE washer not spinning or agitating?

Common solutions for: GE Washer won’t spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. … If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission.

Can you use a washing machine without the agitator?

A washer without an agitator tends to use less water and energy. … They are gentler on clothing and can handle larger items, such as blankets and quilts, sleeping bags, bathroom rugs and other items that an agitator simply can’t handle.

Why is my GE washer not agitating?

If the washer is not agitating, you may need to reset your washer motor. If your washer senses a power spike, an unbalanced load or disruption in power, it will send a fault code to the motor and may require the motor to be reset. … Plug the washer back in and lift and lower the lid 6 times within a 12 second period.

Why is my washer agitator slow?

If the washer is overloaded the top part of the agitator may turn slowly. If the agitator dogs and cam are stripped then the top part of the agitator (auger) might not turn at all. The problem can be with the bolt being loose, the agitator dogs are stripped out or the transmission is the problem.

How do I know if my washing machine agitator is broken?

The agitator should start to oscillate back and forth, mixing up the clothes in the water. If the agitator does not move, double check that the sensor is depressed. If it still does not move with the sensor depressed, the agitator is broken and should be repaired.

Do clothes get clean if agitator is broken?

Damaged Agitator It’s also possible that the agitator isn’t spinning and locking properly due to a mechanical failure. This can have a direct impact on the cleanliness of your clothing – as we said above, the agitator gets the clothing moving, and that movement and friction is key to fresh clothes.

How do you take the front off of a GE front load washer?

1. Unplug the GE washer from the outlet. …
2. Pull out the soap dispenser. …
3. Remove the screws holding the top panel on the washer in place. …
4. Remove the screws holding the control panel in place. …
5. Remove the kick panel beneath the washer door.

Which cleans better impeller or agitator?

Impeller: Which washes better? Washing machines with an impeller tend to wash your clothes better than with an agitator. That means that, generally speaking, front load washers or top load washers without an agitator will do a better job at getting rid of tough stains and dirt off your clothes.

Article first time published on

What's the difference between impeller and agitator?

The Difference Between Agitator vs. Washing machines with agitators use a central post that twists back and forth, rubbing against clothes to help break apart stains. In contrast, washing machines with impellers use a low-profile cone or disc that spins/rotates to rub clothes against each other to get them clean.

Why is my GE washer not dispensing fabric softener?

The fabric softener will not siphon out of the dispenser properly if it is too thick. If the fabric softener will still not dispense after being diluted and verifying proper flow through the dispenser drawer, you could have a component failure in the dispenser assembly or a control problem.

How do you unblock a fabric softener dispenser?

Pour hot water into the dispenser. Add a few drops of liquid detergent and allow the solution to sit for 10 to 20 minutes. Flush the dispenser with hot water. If fabric softener is visible inside the dispenser, wipe it up with a soft cloth and rinse again.