Parging cement consists of sand and Portland cement, sometimes called a sand mix. The mix becomes a sticky substance when you add water. The product’s consistency must be sticky so it solidifies onto a vertical structure without sliding down.

How do you make a parging mix?

For a quality parging mix its best to use a mix of about about 3 parts sand to at least 1 part portland cement. You can add 1/4 to 1/2 part lime powder to make it a little easier to spread or apply. This is mixed with enough water to get a nice consistency, not too runny.

What's parging mix?

Parging is made from a blend of lime, water, and cement. Adding the proper types and amounts for blending can be challenging, as it is a very tricky mixture to master.

What type of mortar is used for parging?

Type S Masonry mortar is recommended for use in all masonry be- low grade as well as in exterior load bearing walls requiring high strength. Type N Masonry Cement or Type S Masonry Cement can also be used in parging and stucco work.

Is Parge the same as stucco?

Parging is a construction technique used to finish the surface of a masonry wall. It is similar to stucco, but uses a masonry-based mortar rather than a traditional stucco mixture. This material can be installed over new or existing walls, and it is used in both residential and commercial applications.

Can you Parge over old parging?

Applying a new layer of parging on top of an old layer is useless because it will also crack and fall off. It’s therefore advisable that you get rid of the parging that’s already damaged. Since you can’t remove the old parging with your bare hands, you will need a cold chisel and a mallet.

What can I use instead of parging?

You can use acrylic stucco as a viable option for parging over concrete foundation walls. However, not all concrete foundation walls can effectively be parged using acrylic stucco. This kind of parging system comprises the last three layers Exterior Insulation and Finish Systems, commonly referred to as EIFS.

How do you fix cracks in parging?

Start by chipping away at the cracked/loose concrete with a concrete chisel. Then brush the area with a wire brush—that will get rid of any loose bits, dust and debris. Then hose off the entire area with water. You can also add a little dish soap—parging sticks better to a clean surface.

Can you Parge with refractory cement?

Hydraulic-setting refractory mortar is the best all-around choice. It can be used to lay the firebrick, set or parge the throat and smoke chamber, and set clay flue liners. It has the workability of ordinary portland-based mortar and can be made almost any shade using ordinary mortar color.

Do you need a bonding agent for parging?

Parging mix sticks to walls better when they’re free of dirt and debris. When applying parging over painted walls, coat the walls with a bonding agent before you begin. This bonding agent will help the mortar bond more successfully with the painted surface.

Article first time published on

What is the purpose of Parging a block wall foundation?

Parging is the coating applied to the visible (above-grade) portion of your home’s foundation walls. It is applied to both poured-concrete and concrete-block foundations to hide surface imperfections, marks from formwork and the like, so its role is essentially decorative.

Can you Parge over Styrofoam?

PARGING OVER EXPOSED RIGID FOAM INSULATION HAS NEVER BEEN SO EASY. COVERAGE: A 25kg pail of Parge-Plus will cover approximately 7.0m (75ft). It will cover slightly less if you’re covering a very rough surface, or trying to achieve a thick, highly-textured look.

How long should Parging last?

Parging mix must be fully cured (approximately 28 days) and dry before painting. Refer to paint manufacturer directions for application instructions.

What is the best parging mix?

Use SAKRETE Parging Mix, a cement mixture designed to create superior bonding, or to smooth concrete walls. Available in 25 KG bags. Go with SAKRETE, The Pros Choice since 1936. Parging Mix, 25 KG is rated 4.8 out of 5 by 33.

Can I use mortar mix for parging?

A person shouldn’t substitute mortar for sand mix when preparing parging cement. Mortar may stick to the blocks or concrete structure after drying; however, over time it crumbles, falling off the structure. You will have to repeat the parging cement process again using the correct material.

Does parging waterproof?

How Can We Help? Parging and sealing are absolute musts for foundation walls with exterior insulation, brickwork, or other materials. While parging is not exactly the same as waterproofing, it is an added layer of protection against moisture.

Should you paint parging?

Why Not Paint Concrete? Applying parging to foundation walls helps to provide a first layer of defense against the exterior elements. … Paint, and especially acrylic paint, does not have these moisture-transferring properties. That means if the paint cracks, and it will, water can seep behind it and has nowhere to go.

Why is my parging cracking?

Why Do Parging Cracks Appear? Although used as a moisture barrier, parging itself can sometimes become wet. When this happens, the water inside the parging can freeze and expand – resulting in cracks.

Can you paint instead of parging?

Short answer; you definitely can, but you shouldn’t. Assuming that the concrete foundation is grinded and rasped to the perfection (which is feat in itself already) the paint will only serve as a decorative purpose. Not only that, it will start chipping away and peeling off soon enough.

How do you make Parging smooth?

Start at the bottom corner of one wall and in a single smooth motion, smear the mortar upward 2 to 3 feet from your starting point. Repeat, overlapping each new smear with the previous one until you have covered the whole wall. Dip the trowel in water to smooth the parged surface.

How do you use quikrete Parging mix?

1. SURFACE PREPARATION. Surfaces must be structurally sound. Remove all sand, dirt, dust, paint, etc. …
2. MIXING. Empty contents of bag into a clean mixing container. …
3. APPLICATION AND FINISHING. Using a trowel, apply not more than ⅜ inch thick. …
4. CURING. After final set, keep damp for 72 hours by misting occasionally with water.

Can I Parge a wall with mortar?

Parging is the application of mortar to the surface of a masonry wall. The result is a form of stucco, or cement-based plaster. To apply it, mortar is troweled onto the wall and spread over the surface in a thin layer.

What is the difference between refractory mortar and refractory cement?

Refractory cement, also known as refractory mortar, is what’s used to secure the bricks together and create the desired structure. It has an improved thermodynamic property in comparison to regular mortar, making it the perfect compliment to firebrick.

What is the best adhesive for stucco?

Super glue works on stucco, like it does on most surfaces.

What is acrylic Parging?

An Acrylic Parge Coating is a Finish that can be Applied on the Interior and / or Exterior of your Home. … This Acrylic Coating Offers Flexibility when your Home has Movement. This Flexible Coating is Less Prone to Cracking.

What adhesive works best on concrete?

SAKRETE Concrete Glue is a liquid latex bonding adhesive for bonding new concrete, mortar or gypsum plaster to existing surfaces. Ready to use and easy to apply, it eliminates the need for roughing or scoring old surfaces.

What is Chimney Parging?

The most common repair to your chimney’s smoke chamber — which serves to funnel smoke from the fireplace opening into the flue — is parging. Parging is a coating of mortar applied to the brick to give the smoke chamber a smooth surface. … During a chimney fire, the parging is often cracked and damaged.

How much does it cost to Parge a foundation?

Parge foundation walls $3 – $4 / sq. ft. Damp proof foundation walls and install weeping tile $60-$120 / lin. ft.

Can you parging ICF foundation?

Parge or coat above-grade ICF block walls! Use this cement-based material to finish Insulated Concrete Form (ICF) block walls or other Expanded Polystyrene Surfaces (EPS). This product is designed to be applied to above-grade portions of ICF foundation walls with a maximum, single coat thickness of 3 mm (1/8”)*.

How do you protect foam insulation from foundation?

Insulation Protection There is no perfect material for covering and protecting exterior foam on foundations. Use metal or plastic reinforcing to strengthen the cement parging on foundation foam boards. The most common approach is to apply a stucco-like “parged” finish with a surface-bonding cement.

How do you protect exposed foundation?

1. Treat the outside of the concrete foundation with soak in invisible water repellent.
2. Apply exterior grade latex paint.