SER is a type SE (service entrance), Style R (reinforcement tape) cable, used as an above ground service entrance cable, a panel feeder and in branch circuits. It is most often used to deliver power from the service drop down to the meter base, and from the meter base to the distribution panel board.

What is the difference between ser and SE cable?

Basically, SER is a round service electrical cable that typically has up to four conductors and a bare neutral. … SEU is an unarmored Style U flat service electrical cable with two-phase conductors and a concentric neutral.

What is #2 Ser cable rated for?

The cable is rated at 600 volts and 90_C for use in wet and dry locations. SER cables are LEAD FREE and RoHS compliant.

What type of wire is aluminum ser?

Insulation: Aluminum SER cable has a type XHHW-2 cross linked polyethylene (XLP) insulation. The conductors are cabled together with a bare aluminum ground and covered with a reinforced binder tape.

What type of insulation is on Ser cable?

Southwire Type SE cable is constructed with Alumaflex® AA-8000 series aluminum alloy, compacted stranded conductors. The conductors are covered with a sunlight resistant Type XHHW-2 or Type THHN/THWN-2-insulation.

Can you direct bury Ser cable?

For direct burial aluminum cable for underground distribution, please take a look at our selection of Aluminum URD Wire, or visit our direct burial cable archive. … We offer Aluminum SER Wire in sizes 6 AWG – 4/0 and can cut to any length you need!

What is SER wire stand for?

Aluminum Service Entrance Cable Product Selection (SER Cable) SER is a type SE (service entrance), Style R (reinforcement tape) cable, used as an above ground service entrance cable, a panel feeder and in branch circuits.

What kind of wire do I need for a 200 amp service?

Wiring 200 amp service requires either #2/0 copper wiring or #4/0 aluminum or aluminum clad wiring. Which wire used is determined by the voltage drop and length of the wiring. Many electrical contractors opt to use #4/0 aluminum or copper-clad wire.

Can Ser cable be run in conduit?

SE cables simply can’t be buried, conduit or no conduit.

How many amps will #6 aluminum wire carry?

Conductor Size (AWG/KCMIL)60°C (140°F) TW, UF75°C (167°F) RHW, THHW, THW, THWN, XHHW, USE, ZW83540640504556536575

Article first time published on

What is #4 Ser rated for?

Cable TypeService Entrance CableLocation UseWet, DryStandardsUL Listed

What size wire do I need for a 125 amp service?

SERVICE ENTRANCE CONDUCTORS SIZE AND RATINGService or Feeder RatingCopper ConductorsAluminum or Copper-Clad Aluminum100 Amps#4 AWG#2 AWG125 Amps#2 AWG#1/0 AWG150 Amps#1 AWG#2/0 AWG

Can you use ser for range?

SE cables are often used for larger branch circuits in residential installations to supply appliances such as ranges, dryers and air conditioners.

What is the primary difference between NM and NMC cable?

Type NM cable is defined as insulated conductors enclosed within an overall nonmetallic jacket, while Type NMC is insulated conductors enclosed within an overall corrosion-resistant nonmetallic jacket. The only difference between the two definitions is that NMC is corrosion-resistant and NM cable is not.

What is #6 aluminum rated for?

CopperAluminum84040655504706538575

How often does Ser cable need to be supported?

When used as a branch circuit or feeder, Type SE cable must be supported and secured in accordance with 334.30 at intervals not exceeding 4½ feet and within 1 foot of every outlet box, junction box, cabinet or fitting.

What type of wire is used for overhead service?

Triplex wire is commonly used for overhead, single phase service and contains three individual wires twisted around each other. The two insulated conductors are called the “hot” legs of the service while the bare (uninsulated) wire is the neutral wire of the service.

What type of wire is used for service entrance?

Service entrance cable are usually of two types: SER or SEU. SER cable is SE (Service Entrance) Style R, which has a reinforcement tape and may be made of copper or aluminum. SEU cable is SE (Service Entrance) Style U, which means it is unarmored.

Is Ser cable underground rated?

SER is not rated for underground use, but USE is. 2-2-2-4 aluminum is allowed for 100 amp feeders in many areas.

Is Ser cable waterproof?

Enclosures installed in wet locations shall be weatherproof. For enclosures in wet locations, raceways or cables entering above the level of uninsulated live parts shall use fittings listed for wet locations.

What type of wire can I run in conduit?

The most common type of cable used in home wiring is non-metallic (NM), or Romex, cable. While NM cable can be run inside a conduit, this is seldom done. The types of wire most commonly installed inside of conduit are THHN and THWN. THHN/THWN wires are individual, insulated, and color-coded wires.

What size of wire is needed for a 100 amp service?

When it comes to the lines connecting master and secondary panels, where the line will carry as much as a full 100 amps, use a 2-gauge non-metallic sheathed electrical cable. The cable must contain one or two hot wires depending on your needs, one neutral wire, and one ground wire. Each wire should be 2-gauge in size.

What size copper wire do you need for 100 amp service?

A 100 amp sub panel wiring size requirement is #4 for copper wires and #2 for aluminum wires.

What wire goes from meter to panel?

Electrical wire Based on the current and voltage rating of the meter and breaker, #4 size AWG copper wire is the highly suggested type and size of wire. This is to provide efficiency in conductivity; it will also prevent unnecessary loss of power, short circuit, damages, even wiring faults that may lead to dangers.

What size of wire do I need for a 60 amp breaker?

For 60 ampere breakers, electricians and professionals suggest using a wire size gauge ranging from 6 AWG to 4 AWG. All household wires have a rating of at least 600V, so only amperage really matters when it comes to determining wire gauge.

What size wire do I need for a 500 foot run?

500 Feet – a 120-volt, 20 amp circuit would require 1/0 AWG wire. A 240 volt, 30 amp circuit would require 3/3 AWG wire.

How many amps is number 8 Romex good for?

NM, TW, & UF WIRE (Copper Conductor)SE CABLE (Copper Conductor)12 AWG – 20 AMPS6 AWG – 65 AMPS10 AWG – 30 AMPS4 AWG – 85 AMPS8 AWG – 40 AMPS2 AWG – 115 AMPS6 AWG – 55 AMPS1 AWG – 130 AMPS

How many amps is #2 SEU good for?

Cable TypeSEUAmpacity100

How many amps can 350 mcm carry?

SizeTemperature Rating of Copper Conductor(AWG or kcmil)60°C (140°F)90°C (194°F)350 KCMIL260350400 KCMIL280380500 KCMIL320430

What size wire is used for a 100 amp subpanel?

The cable must have a wire gauge sufficient to the amperage of the subpanel—a 100-amp subpanel requires #4 copper wires or, more commonly, #2 aluminum wires, for example.

What size wire do I need to run 100 Amp Service 150 feet?

What is the right wire size for 100 Amp service 150 feet distance? You should get 2/0 AWG Copper wire or 4/0 AWG Aluminum wire for single-phase circuits. And, 1/0 AWG Copper wire or 3/0 AWG Aluminum wire if you have three-phase circuits. For these wires, the average voltage drop should be 3%.