Rough sawn lumber comes in “true” thicknesses as reflected by the “quarters” size. Lumber sized according to “Quarters” reflects the number of quarters of an inch thick the lumber is. To figure the thickness of a board referenced in “quarters” sizes, simply divide the second number (4) into the first number.

Why is lumber not the actual size?

The “nominal” cross-section dimensions of a piece of lumber, such as 2 X 4 or 1 X 6, are always somewhat larger than the actual, or dressed, dimensions. The reason is that dressed lumber has been surfaced or planed smooth on four sides (called S4S). The nominal measurement is made before the lumber is surfaced.

Why wood is really measured to a half in less?

Through the drying process, the boards naturally shrink, as moisture leaves the beams. … Without the rough edges, what went in as a 2-by-4 planks of rough-sawn wood is now a tongue-tripping 1.5-by-3.5, having lost approximately ¼-inch on all sides to the planer and drying processes.

Why is it called 5 4 board?

Quarters refer to the thickness of rough-sawn lumber measured in ¼-inch increments. Instead of reading it as a fraction, it should be read as a number of quarters: 5/4 is five quarters, 4/4 is four quarters, etc.

What does quarter mean in lumber?

By definition, quarter sawn lumber is the angle that the annular growth rings intersect the face of the board. … When cutting this lumber at the sawmill, each log is sawed at a radial angle into four quarters, hence the name.

Why 2x4 is not 2x4?

DIMENSIONAL LUMBER: In the past, when a timber was called a 2×4 [or “two-by-four”], it actually measured 2 inches by 4 inches. … Because of this extra milling, a 2×4 no longer measures a full 2 inches by four inches. Instead, a 2×4 is really only 1 1/2″ by 3 1/2″.

Why is lumber smaller than the size it says?

Typically, that rough cut is smaller than the nominal dimensions because modern technology makes it possible to use the logs more efficiently. For example, a “2×4” board historically started out as a green, rough board actually 2 by 4 inches (51 mm × 102 mm).

Can I use 2x6 for deck boards?

Wood decking is commonly available in 2×6 and 5/4 x 6 profiles. 5/4 x 6 is produced specifically for decking and is milled with a radius edge or bull nose. 2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions.

What does BF mean in lumber?

1. Hardwood lumber is typically sold by the board foot, a unit of volume equivalent to a board that is one inch thick, one foot wide and one foot long, or 144 cubic inches.

What is the true thickness of 5/4 lumber?

Nominal SizeRough SizeActual Size: Surfaced 2 Sides–3/4 inch9/16 inch (14 mm)4/4 inch1 inch13/16 inch (21 mm)5/4 inch1 1/4 inch1 1/16 inch (27 mm)6/4 inch1 1/2 inch1 5/16 inch (33 mm)

Article first time published on

When did they stop making true 2x4?

This pressured further compromise because thinner 2x4s were a way to compete in price with wood alternatives. Size standards, maximum moisture content, and nomenclature were agreed upon only as recently as 1964. The nominal 2×4 thus became the actual 1½ x 3½, imperceptibly, a fraction of an inch at a time.

Why is a 4x4 actually 3.5x3 5?

no, it is just a bit over 3.5″x3. 5″ for clearance. 2×4 and 4×4 boards are no longer the actual number, but as you state–they are 1/2″ LESS. the base fits nicely to a standard 4×4.

Why are the actual dimensions of lumber different from the nominal dimensions?

Actual measurements are the actual final size of the lumber after it has been dried and planed. Boards will shrink width-wise versus length-wise because of the direction of the grain. This is because wood is anistrophic, meaning that the wood’s properties will change depending on the grain direction.

What is the advantage of quarter sawn lumber?

Some advantages of quartersawn lumber: Shrinks and swells less in width. Cups, surface-checks, and splits less in seasoning and in use. Raised grain caused by separation in annual rings does not become as pronounced.

What are the disadvantages of quarter sawing?

More expensive than plain sawn material Quarter sawn wood is more expensive because it is more labor intensive to produce and the manufacturing process produces more waste than plain sawn lumber.

How is wood measured?

The board foot is the most common standard used for saw logs and lumber. A board foot contains 144 cubic inches of sawed lumber or the equivalent of a board 1 inch thick, 12 inches wide and 1 foot long. A second unit of measure is the cord. … The standard cord is a pile of wood 4 feet high, 4 feet wide and 8 feet long.

Why is lumber so expensive?

Lumber is expensive due to supply and demand and the various factors that influence both. Thanks to the COVID-19 pandemic and inflation, suppliers have had a difficult time filling the gap in lumber demand as well as meeting the current demand for wood. Lumber doesn’t have to be expensive, however.

What does 2x4x8 mean?

The 2 tells us the thickness of the board in inches, the 4 is the width of the board in inches and the 8 is the length of the board in feet.

Is lumber a renewable resource?

Wood is a renewable resource, which means that additional resources can be grown to replace any wood that is cut down.

Why do they make 92 5/8 studs?

To create a wall that will match up with a typical 4×8 sheet of drywall, the studs need to be a little shorter — 92 5/8” to be exact. This also allows a little extra room along the bottom of the wall for variances in flooring and to keep the drywall from soaking up moisture from the floor.

What does it mean when someone calls you 2 by 4?

Frequency: A length of lumber that is 2 inches thick and 4 inches wide, or that is trimmed to slightly smaller dimensions.

When did lumber dimensions change from actual to nominal?

Early concepts called for rough lumber to be of full nominal size, often in the dry condition. After World War I, the increasing demand for construction lumber led to the first national size standard in 1924. This was revised in 1926, 1928, 1939, and 1953, while still another revision is proposed for adoption in 1964.

What is the price of black walnut per board foot?

HOWEVER, the going stumpage rate for quality black walnut right now is around $0.80 – $2.00/bd ft for sawlogs (used to make lumber) and $3.00 – 10.00/bd ft for veneer logs (used to make fine face veneer for furniture, architectural paneling, etc.).

What does BD mean in woodworking?

Board Foot: BF or Bd. Board Foot is a volume measure of lumber. It is calculated using the dimensions of the lumber in the rough. This means that it uses the measurement of a board prior to planing or the application of a straight-line rip.

What is a super foot of timber?

noun. Building. A square foot. In later use specifically (chiefly Australian and NZ) a square foot of timber of a specified thickness, usually one inch.

Should deck boards have a gap?

Proper wood deck board spacing should have at least a 1/8 inch gap after the decking has dried out. If you install your wood or treated deck boards while they are still wet boards, then they should be attached without a gap between them.

Can you use 1x6 for deck boards?

Never use 1×6 or 5/4×6 material in close to ground applications. Spacing between boards: You must allow space for your deck boards to expand when they take on moisture, as they will inevitably do when exposed to wet weather, rain or high humidity.

Should a deck be built with 2x6 or 2x8?

For upper-level decks, 2×10 is recommended as the minimum size to use for strong guard post connections. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. … Most decking is not strong enough to support longer spans than 16″.

Why do 2x4's have rounded edges?

2×4 have rounded edges as it’s very beneficial to the wood itself and those working with it. They reduce the number of injuries like unwanted splinters during the handling and manufacturing process and also ensure that the lumber stays looking its best all throughout until the customer sees it.

What is the difference between nominal and dimensional lumber?

Why are the nominal dimensions of lumber larger than the actual dimensions? The simple answer is the nominal measurements were derived from a board’s size before it has been dried and planed smooth (surfaced) on all 4 sides. The actual measurements are the final dried and surfaced size.

What's the actual size of a 2x10?

Nominal SizeActual Size2 x 81 1/2 x 7 1/4 inches (38 x 184 mm)2 x 101 1/2 x 9 1/4 inches (38 x 235 mm)2 x 121 1/2 x 11 1/4 inches (38 x 286 mm)4 x 43 1/2 x 3 1/2 inches (89 x 89 mm)