The rope grab is the device that allows the worker to move up and down a vertical lifeline. … The manual rope grab is basically a metal hand trigger. When you hold the rope grab down, you are able to move freely up and down the rope. Once you let go, the rope grab latches to the rope and will no longer move up and down.

What is a rope grab?

A rope grab is a deceleration device that is part of a personal fall arrest system (PFAS). It travels on a lifeline and automatically engages and locks to arrest a fall. … Rope grabs are used along with vertical lifelines on which the rope grabs can travel up and down.

How does a grab fall arrester work?

Fall arrest device that travels up and down a vertical lifeline rope. It grabs the rope via a cam design that locks a fallen worker in place on the lifeline. The cam and hinge design also allows for quick and easy installation on the rope. …

How does a rope adjuster work?

The Rope Adjuster is a Type 1 Fall Arrest Device which locks off onto the rope at any point. This is a manually operatable unit. With the Manual unit there is a need to squeeze the unit to release the rope jaws; this will allow the operator to move the unit along the rope.

Can rope grabs be used horizontally?

Retractable fall arresters are commonly used with overhead anchorage lines but nowadays, more and more models are suitable for horizontal use too. …

What is the maximum length that a lanyard can be when attached with a rope grab to a vertical lifeline?

This is why it’s of the utmost importance to follow manufacturer instructions for lanyards. Manufacturers will outline the proper connector length limit, which is 30” in Canada and may differ elsewhere.

What is lifeline rope?

In simplest form, a land-based lifeline consists of a horizontal wire rope cable attached to two or more anchor points on a roof-top, crane runway, bridge or outdoor construction site, or any other elevated work area that poses a fall risk.

How are rope grabs oriented to the lifeline?

rope grab to a lifeline, always make sure the arrow on the device points along the lifeline towards the anchor point (pictured). grab on the lifeline, give it a firm tug in the direction of a fall to make sure it engages. that locks at a point on the lifeline that won’t let you reach a fall hazard.

What is fall prevention equipment?

So lifelines or anchors are installed to safeguard workers exposed to fall risks and the persons are equipped with fall arrest systems attached to their body harnesses so that when (not if) they fall the combination of the anchor and fall arrest system prevents the person from falling over too long a distance and is …

What direction does the orientation arrow on a rope grab point?

Rope Grabs(RG) and Fall Arresters(FA) must be installed with the direction arrow pointing to the anchorage end of the lifeline. Failure to do so will result in serious injury or death in the event of a fall.

Article first time published on

How many types of fall arresters are there?

Personal fall arrest systems Fall arrest is of two major types: general fall arrest, such as nets; and personal fall arrest, such as lifelines.

What is retractable fall arrester?

A retractable fall arrester is Personal Protective Equipment designed to arrest a fall and to limit the impact generated by the deceleration, without causing injuries to the user’s body.

What is a harness used for?

The harness serves two purposes: first, distributing fall forces safely across a worker’s body in the event of a free fall, and second, providing freedom of movement sufficient to allow the worker to effectively perform his or her job.

How do you inspect a rope grab?

1. Inspect for physical damage, cracks, wear, and corrosion.
2. Check cam and/or springs for damage or loss of tension.
3. Check pawl and locking mechanism.
4. Check that all parts move freely without hesitation.

What is an elevator rope gripper?

A rope gripper is a machine that is hydraulically reset and mechanically activated to grip the elevator suspension ropes to protect an elevator in case there is an electrical or mechanical failure.

What is the size of life line rope?

Depending on the brand, lifeline ropes are available in various lengths with hooks. The hooks may be heavy duty or double locking snap hooks or self-locking snap hooks. The lengths typically available are 25 feet, 50 feet, 75 feet, 100 feet, 150 feet, 200 feet, and 250 feet.

How do you identify different types of rope?

The marker tape is a conclusive way of identifying a rope material, when it can be found. In an unspliced rope, the marker tape can be found by untwisting the end of a strand. In broken rope, it may be found by careful disassembly of the rope.

What is polyester cord?

Polyester rope and cord, also commonly called Dacron, will provide similar strength to Nylon rope with less stretch and better abrasion resistance. … Applications polyester rope is well-suited for include boating and marine use, rigging, outdoor use, and general purpose. Polyester rope does not float.

What is the best height to position your anchor at?

Use the shortest length lanyard that still allows the worker to perform their work safely. The lanyard should be attached to an anchor that is not lower than the worker’s shoulder height (unless an anchor at shoulder height is not possible).

How many workers can tie to a vertical lifeline?

Each vertical lifeline can be used by only one person at a time (Figure 19-10). A vertical lifeline must reach the ground or a level above the ground where the worker can safely exit after the fall has been arrested.

What are bump lines?

Warning barriers and bump lines prevent falls by alerting workers to fall hazards. Warning barriers and bump lines should be set up around the work area at least 2 metres (6 feet 6 inches) from unprotected edges.

What are the 4 methods of fall protection?

All active fall protection for the construction industry falls into four basic categories: fall arrest, positioning, suspension, and retrieval. OSHA provides standards for each category of fall protection.

Can you connect two lanyards together?

In summary, if two lanyards are hooked to one another with locking snaphooks, and one end is connected to a safety line and the other to a harness, the snaphooks must be designed by the manufacturer for such use. Care should be taken to ensure that sufficient distance exists for complete fall arrest to occur.

At what height do you need a harness?

Personal Fall Arrest Systems OSHA requires workers to wear a full-body harness, (one part of a Personal Fall Arrest System) when they are working on a suspended scaffold more than 10 feet above the working surface, or when they are working in bucket truck or aerial lift.

What does 100 tie off mean?

Related Definitions 100% tie-off means that a person must be properly tied-off at all times while exposed to a fall hazard. The use of two lanyards is required if a person must move or relocate a tie-off point while exposed to a fall hazard to ensure a positive tie-off connection at all times during the move.

Can two people tie off to the same anchor point?

An HLL, such as one of our Cable or Big Boss HLLs, can be an especially effective solution by allowing multiple workers to be tied off to the same anchor (remember, an HLL is a type of anchor), yet giving them the freedom to work together or apart, and to move freely without the necessity of changing anchors.

What is the minimum required tensile strength of a snap hook?

D-rings and snaphooks shall be proof-tested to a minimum tensile load of 3,600 pounds (16 Kn) without cracking, breaking, or being permanently deformed.

When putting on a harness and tightening it where should the D ring sit?

The D-ring should rest squarely in the middle of the back between your shoulder blades. To adjust, slide the D-ring and plaque up or down along the webbing. It should never be off to one side, too low, or too high. Shoulder straps should remain vertical and evenly spaced on the chest.